BLOG DUKE AMIENE REV

Isnin, November 21, 2011

Charging Battery Using USB Port - ICD-UX200F

FULL CHARGING TIME: It takes about 3 hours and 30 minutes to fully charge an exhausted battery for ICD-UX200/UX300/UX400/UX200F/UX300F/UX400F. 

Is it possible to charge the battery using a USB port on the computer? 
Question: Charging the battery using a USB port on the computer. 

Answer: Yes, it is possible. Using AAA Nickel hydride rechargeable battery, the battery will be charged when the IC recorder is connected to the computer. However, even though the computer is turned on, you cannot charge the batteries while your computer is in the sleep, standby or hibernation mode. In such cases, change the settings on your computer so that your computer will not go into sleep, standby or hibernation mode. This is an approximate time it takes to charge from an empty battery power to a fully battery power at room temperature. It varies depending on the remaining power and the condition of the battery. It also takes more time if the temperature of the battery is low, or if the battery is charged while you are transferring data to the IC recorder. Notes In case USB CHARGE in the DETAIL MENU is set to OFF, the battery will not be charged even though the IC recorder is connected to the computer. While HOT or COLD is being displayed on the display window, the batteries cannot be charged. Charge the battery in an environment with a temperature range between 5 Celsius degree to 35 Celsius degree. It takes about 3 hours and 30 minutes to fully charge an exhausted battery for ICD-UX200/UX300/UX400/UX200F/UX300F/UX400F. 

Why does not the battery charge start even though the IC recorder is connected to a USB port on the computer? Article ID:352461(modified 23 Feb 2011) 
Applicable Models Question Battery charge does not start even though the IC recorder is connected to a USB port on the computer. Answer In the following cases, it will not be possible for you to charge the battery. The computer is turned off. After turning on the computer, connect the IC recorder. However, even when the computer is turned on, you will not be able to charge the IC recorder if your computer is in the sleep, standby or hibernation mode. In such cases, please change the settings on your computer so that your computer will not go in the sleep, standby or hibernation mode. The battery is inserted with incorrect polarity. Please check the polarity of the battery and insert it with correct direction. USB CHARGE of DETAIL MENU in the menu is set to OFF. To charge the batteries using your computer, set it to ON. System requirements of the computer have not been met. For the necessary system requirements, please refer to - System requirements of the computer for using IC recorder as a USB mass storage device. A USB hub or a USB extension cable is used. Connecting the IC recorder with a USB hub or a USB extension cable is not guaranteed. Connect the IC recorder directly to the computer. More than two USB devices are connected to the computer Connecting more than two USB devices to the computer is not guaranteed. Connect only the IC recorder to the computer. Playing back messages or files using the built-in speaker While playing back messages or files using the built-in speaker, you cannot charge the battery. Stop the play back, and then connect the IC recorder to the computer. HOT or COLD is flashing on the display window on the IC recorder. While HOT or COLD is flashing instead of the remaining battery/charging indicator, the battery cannot be charged. Charge the battery in an environment with a temperature range between 5 Celsius degree to 35 Celsius degree. Alkaline battery is used. To charge the battery, use the nickel hydride rechargeable battery. If the battery charge does not start even after checking the above, a connection error might be a cause. Please check the connection to the computer with the steps below. Remove the IC recorder from the computer and connect it again. When the computer has two or more USB connectors, try to connect to another USB connector. Remove the IC recorder from the computer, restart the computer and connect it again. Note: While charging the battery, CONNECTING and the charging indicator are displayed in an animation. When the charging indicator indicates FULL HOT, battery charge is completed. Charging time is approximately 3 hours and 30 minutes.